withstand voltage isolation resistance i/p-o/p:3.75kvac i/p-fg:1.88kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh constant current region note.4 hlg-100h-20 a specification model dc voltage rated current rated power output voltage adj. range note.6 current adj. range line regulation load regulation setup, rise time note.8 hold up time (typ.) voltage range note.5 frequency range power factor efficiency (typ.) ac current input inrush current( .) typ leakage current safety standards note.7 harmonic current ems immunity working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current note.4 over voltage over temperature can be adjusted by internal potential meter or through output cable 2500ms, 50ms / 115vac ; b type 2500ms, 200ms at 95% load 230vac / 115vac at full load 230vac 16ms at full load 230vac /115vac 90 ~ 305vac 127 ~ 431vdc 47 ~ 63hz pf 0.95/230vac pf 0.98/115vac at full load and rated output voltage pf 0.9 at 60 ~ 100% load 1.2a / 115vac 0.55a / 230vac 0.5a / 277vac cold start 75a/230vac <0.75ma / 277vac 95 ~ 106% compliance to en55015 , en55022 (cispr22) class b compliance to en61000-3-2 class c ( 60% load) ; en61000-3-3 -40 ~ +60 @ full load ; +70 @ 60% load (refer to derating curve) 20 ~ 95% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 5g 12min./1cycle, period for 72min. each along x, y, z axes 192.2 khrs min. mil-hdbk-217f (25 ) 220*68*38.8mm (l*w*h) 100w single output switching power supply features : h l g - 1 0 0 h s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment emi conduction & radiation safety & emc protection 100 10 (rth2) protection type : shut down o/p voltage, recovers automatically afte r temperature goes down short circuit 23 ~ 27v 28 ~ 34v 34 ~ 38v 41 ~ 46v 54 ~ 60v 47 ~ 53v 59 ~ 65v 93% 93% 93% 93% 93% 93% 93% 1.0% 1.0% 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 1.0% 0.5% 0.5% 1.0% 0.5% 0.5% 20v hlg-100h-20 hlg-100h-30 hlg-100h-42 HLG-100H-54 hlg-100h-24 hlg-100h-36 hlg-100h-48 10 ~ 20v 24v 12 ~ 24v 30v 15 ~ 30v 36v 18 ~ 36v 48v 24 ~ 48v 150mvp-p 17 ~ 22v 150mvp-p 22 ~ 27v 200mvp-p 27 ~ 33v 200mvp-p 33 ~ 40v 200mvp-p 43 ~ 53v 54v 27 ~ 54v 200mvp-p 49 ~ 58v 42v 21 ~ 42v 200mvp-p 38 ~ 46v universal ac input / full range (up to 305vac)built-in active pfc function protections: short circuit / overload / over voltage / over temperature cooling by free air convection ocp point adjustable through output cable or internal potential meter ip67 / ip65 design for indoor or outdoor installations three in one dimming function (1~10vdc or pwm signal or resistor) suitable for led lighting and street lighting applications compliance to worldwide safety regulations for lighting 5 years warranty (note.10) suitable for dry / damp / wet locations high efficiency up to 93% a : ip65 rated. output voltage and constant current level can be adjusted thr ough internal potential meter. b : ip67 rated. constant current level adjustable through output cable w ith 1~10vdc or 10v pwm signal or resistor. blank : ip67 rated. cable for i/o connection. 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. constant current operation region is within 62.5% ~100% rated output v oltage. this is the suitable operation region for led related applicati ons, but please reconfirm special electrical requirements for some specific syste m design. 5. derating may be needed under low input voltages. please check the stati c characteristics for more details. 6. type a only. 7. safety and emc design refer to en60598-1, cns15233, gb7000.1, fcc part 18. 8. length of set up time is measured at cold first start. turning on/off the powe r supply may lead to increase of the set up time. 9. the power supply is considered as a component that will be operated in combi nation with final equipment. since emc performance will be affected by th e complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 10. refer to warranty statement. protection type : constant current limiting, recovers automatical ly after fault condition is removed compliance to en61000-4-2,3,4,5,6,8,11; env50204, en61547, en 55024, heavy industry level (surge 4kv), criteria a ul8750, en61347-1, en61347-2-13 independent approved ; design re fer to ul60950-1, tuv en60950-1 ip65 or ip67 constant current limiting, recovers automatically after fault con dition is removed protection type : shut down o/p voltage with auto-recovery or re-power o n to recovery 3 ~ 4.8a 2.5 ~ 4a 2 ~ 3.2a 1.65 ~ 2.65a 1.25 ~ 2a 1.1 ~ 1.77a 1.4 ~ 2.28a 4.8a 4a 3.2a 2.65a 2a 96w 96w 96w 95.4w 96w 1.77a 95.58w 2.28a 95.76w 1.12kg; 12pcs/14.4kg/0.76cuft f m m 110 selv ip65 ip67
mechanical specification case no.994a unit:mm 300 20 300 20 fg (green/yellow) fg (green/yellow) sjtw 14awg 2c sjtw 14awg 2c 38.8 sjtw 18awg 3c sjtw 18awg 3c 220 220 196 196 ac/l(brown) ac/l(brown) ac/n(blue) ac/n(blue) 12 12 9.6 9.6 9.4 9.4 9.4 9.4 34.2 34.2 68 68 4.2 4pl 4.2 4pl 300 20 300 20 +v(red) +v(red) -v(black) -v(black) 38.8 vo adj. io adj. 100w single output switching power supply h l g - 1 0 0 h s e r i e s a type:(hlg-100h-_a) blank:(hlg-100h) file name:hlg-100h-spec 2011-01-31
fosc : 100khz derating curve static characteristics ambient temperature ( ) load (%) -40 -25 -10 0 15 30 50 60 70 20 40 60 80 100 input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 305 100 90 80 70 60 50 40 load (%) (horizontal) dim+ (b type) dim- fosc : 100khz detection circuit emi filter rectifiers power switching filter & rectifiers +v -v i/p fg control o.v.p. & o.l.p. pfc circuit block diagram 300 20 sjtw 18awg 3c 220 196 12 9.6 9.4 9.4 34.2 68 4.2 4pl 300 20 +v(red) -v(black) fg (green/yellow) ac/l(brown) ac/n(blue) sjtw 18awg 2c sjtw 14awg 2c pfc control o.l.p. o.t.p. dim+(blue) dim-(white) pwm 60k 60% 60% 10k 1v 4v 7v 2v 5v 8v 3v 6v 9v 10v 10% 10% 20k 20% 20% 30k 30% 30% 40k 40% 40% 50k 50% 50% 70k 70% 70% 80k 80% 80% 90k 100k open open open 90% 90% 100% 100% resistance value dimming value percentage of rated current percentage of rated current ip67 rated. output constant current level can be adjusted through outpu t cable by connecting a resistor or 1 ~ 10vdc or 10v pwm signal between dim+ and dim-. reference resistance value for output current adjustment (typical ) please do not connect "dim-" to "-v". 1 ~ 10v dimming function for output current adjustment (typical) 60% 60% 10% 10% 20% 20% 30% 30% 40% 40% 50% 50% 70% 70% 80% 80% 90% 90% 100% 100% duty value percentage of rated current 102%~108% 102%~108% 102%~108% 10v pwm signal for output current adjustment (typical): frequency ra nge :100hz ~ 3khz 38.8 100w single output switching power supply h l g - 1 0 0 h s e r i e s b type:(hlg-100h-_b) file name:hlg-100h-spec 2011-01-31
65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 230vac 110vac efficiency vs load (48v model) hlg-100h series possess superior working efficiency that up to 93% can be r eached in field applications. load efficiency (%) there are two major kinds of led drive method "direct drive" and "with led driv er". a typical led power supply may either work in "constant voltage mode (cv) or c onstant current mode (cc)" to drive the leds. mean well's led power supply with cv+ cc characteristic can b e operated at both cv mode (with led driver, at area (a) and cc m ode (direct drive, at area (b). driving methods of led module typical led power supply i-v curve vo(%) 100 50 50 100 io (%) constant voltage area constant current area (a) (b) 0.84 0.86 0.88 0.9 0.92 0.94 0.96 0.98 1 1.02 60% 70% 80% 90% 100% 230vac 110vac power factor characteristic power factor will be higher than 0.9 when output loading is 60% or higher. pf load constant current mode 100w single output switching power supply h l g - 1 0 0 h s e r i e s file name:hlg-100h-spec 2011-01-31
direct driving : under direct driving, the power supply will work in "constant current mod e (cc)" and output voltage of the power supply will be clamped by sum of forward voltage (v ) of the led strip. f the total forward voltage of series connecting leds is suggested for 60%~ 95% of power supply rated output voltage due to concern of the best pf value and efficiency. ac source i/p o/p hlg-100h with led driver using additional driver, the power supply will work in "constant voltag e mode (cv)" and output voltage of the power supply will be kept in rated value. in this drive mode, several design issues need to be considered: 1.output voltage of psu must be higher than total forward voltage of series c onnecting leds by 3v minimum. 2.input capacitor (cin) of led driver circuit should use 47uf ~ 100uf(typ .) of rating depends on the operating frequency of the led driver. the higher the operating frequency is used, the smaller value of cin should b e chosen, and vice versa. ac source i/p o/p ic circuit cin cout v f r l hlg-100h ~ ~ ~ ~ 3.do not use b type with led driver. dimming connection diagram for turning the lighting fixture on/off : using a switch and relay can turn on/off the lighting fixture. using the built-in dimming function on b-type model can't turn the lighti ng fixture totally dark. please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the led power s upply unit. 1.output constant current level can be adjusted through output cable by c onnecting a resistor or 1~10vdc or 10v pwm signal between dim+ and dim-. 2.the led lighting fixture can be turned on/off by the switch. n fg l led lighting relay blue brown green/ yellow ac/l ac/n hlg-100h b type dim+ dim- v(-) v(+) blue white black red switch adjuster 0~100k ohms resistance 1~10v dc voltage 10v pwm signal dimming operation(for b-type only) 100w single output switching power supply h l g - 1 0 0 h s e r i e s file name:hlg-100h-spec 2011-01-31
waterproof connector waterproof connector can be assembled on the output cable of hlg-100h to op erate in dry/wet/damp or outdoor environment. hlg-100h i/p o/p led lamp ac source cable joiner pin configuration (female) pin configuration (female) size size m12 m15 4-pin 5a/pin m12-04 order no. order no. 10a max. suitable current suitable current 5-pin 5a/pin m12-05 10a max. 2-pin 12a/pin m15-02 12a max. up to four wires can be connected through this cable joiner bysoldering or clamping by tools. 66 26 20 25 suitable for 14awg~22awg o/p wires led lamp hlg-100h waterproof connection ~~ ac source i/p fg c b d a a o/p led cc driver chassis of led lamp cc ic hlg-100h a. add a common mode ferrite choke on output wires to reduce the common emissi on between 10m ~ 300mhz per lighting emi regulation. b. chassis of led lamp and chassis of hlg-100h or the fg wire should be connected t o the safety ground to reduce the emi noise, including the conduction and radiation emission. c. the additional x-cap and discharge resistor can reduce the l conduct ion noise between 9k ~ 1mhz per lighting emi regulation. d. l-c filter should be added at the dc input of led constant current driver to avo id the differential emission and high frequency noise generated by the cc driver. ow frequency emi debug suggestion 100w single output switching power supply h l g - 1 0 0 h s e r i e s file name:hlg-100h-spec 2011-01-31
|
